|
|
|
Operant Cage
Accessories |
| Model
15800 White Noise Package This
package includes the control, a 7-watt amplifier, and 4 speakers.
It features a 31-stage pseudorandom noise generator at 20 to
20,000Hz, filtered to remove square wave spikes. |
 |
|
Model 15800C White Noise Control The
White Noise control has a 7-watt amplifier and features a 31-stage
pseudorandom noise generator at 20 to 20,000Hz filtered to remove
square wave spikes.
|
| Model 80221 Stimulus Light
This
light features a large, 1" white frosted lens for distinct
CS presentations, and works off of a standard 28VDC power source. |
 |
|
Model 80223 Sonalert
The
Sonalert provides a 2,800Hz tone at 80dB for use as an auditory
stimulus. Amplitude can be adjusted by varying the voltage
supplied. |
 |
| Model
83619 28 Volt Power Supply This
4A power supply will operate up to 4 operant cages. Multiple
power supplies can be used to increase operations. Short circuit
protection is provided by internal current
foldback circuitry. Dimensions: 12.75"x9.75"x5.5"
|
 |
|
| Model
58011A Photocell Kit This
infrared system uses a separate source and receiver with a range
of up to 12’. A five-way binding post provides connection
to the device. An external DC power source between 10 and 30V
is needed for the device. The output can be configured as either
a normally open or closed switch. The open collector transistor
can switch up to 30VDC at 100mA max.
|
 |
| Model 81413 Basic Photocell Kit
Using
the same infrared sensors as Model
58011A, this unit may
be easily interfaced with the ABET system. It uses a separate
source and receiver with a range of up to 12’.
An external DC power source between 10 and 30V is needed for
the device. The output from the device is a normally open switch.
The open collector transistor can switch up to 30VDC
at 100mA max. |
| Model 82400ss
Master Shocker Supply
This
constant current shocker features two output levels 0 to 1mA
on the front and 0 to 5mA on the back panel. Line voltage required
is 105/125V AC and current regulation is 3 percent for a 50kOhm
change in subject resistance. Grid Harness Model
80001GH is used to connect
the shocker to the operant cage. Dimensions: 10"x7"x5.5"
|
 |
| Model
82404ss Master Shocker with Scrambler This
model features either a direct 0 to 5mA output, or a silent
neon scrambled constant 0 to 1mA with zero crossover. Line voltage
required is 105/125VAC and current regulation is 3 percent for
a 50kOhm change in subject resistance. The voltage regulator
limiter prevents outputs from rising above 1600V at no load.
The interrupter pulses the shock output within a 1-second interval,
(5-100% of 0.05-1 second adjustments). Direct output from the
5-way binding post is a bipolar 60Hz sine wave. Grid
Harness Model
80240A is used to connect
the shocker to the operant cage. Dimensions: 19"x7"x6"
Model
80240A is used to connect
the shocker to the operant cage. Dimensions: 19"x7"x6"
Model
80240A is used to connect
the shocker to the operant cage. Dimensions: 19"x7"x6"
|
 |
| Model 58006
Constant Current Shocker
This
simple unit delivers up to 1mA of current to any subject 100,000
Ohms or less. Line voltage required is 105/125V AC. Current
regulation is 2.5% for a 50kOhm change in subject resistance.
Dimensions: 6"x5.75"x4.75"
|
 |
|
Model 58020 Neon Grid Scrambler
This
device can be used with any of our shocker units. Noiseless
scrambled shock is provided for up to 2mA. Use Grid Harness
Model
80240A to attach to the
operant cage.
Dimensions:
6"x6"x4.5"
|
 |
|
|
|
|
|
|
|
|
